#1
|
|||
|
|||
Jack Plate
Hat jemand ein Jack Plate wie z.B. einen CMC Power Lift übrig?
|
#2
|
|||
|
|||
Ist ja schon ne weile her. Vielleicht hat jetzt jemand was übrig?
|
#3
|
|||
|
|||
Versuche es einmal in GB in boatmad
|
#4
|
|||
|
|||
Danke, aber ich habe dort nichts gefunden.
|
#5
|
|||
|
|||
jack plate
Ich habe ein powerlift im angebot mit 7 cm set back. Manuelle bedienung. Habe es 2017 neu gekauft in der USA und hätte es zum probe am rennboot geschraubt. Hat super funktioniert aber wegen ein riss im boden von boot wegen neuen boden abgeschraubt und nach herr andere motor am boot angeschraubt. Seit dem ist es im lager. Zu haben für € 250,= { ist weniger wie versand und versteuerung aus den USA }
|
#6
|
|||
|
|||
bild
noch bild mit boot
|
#7
|
|||
|
|||
Danke, ja das sieht interessant aus. Was für ein Hersteller ist das?
|
#8
|
|||
|
|||
jack plate
Hersteller: VANCE MANUFACTURING IN TENNESSEE, USA
|
#9
|
|||
|
|||
Danke, kannst du mir bitte noch die Maße durchgeben?
Die Breite und Höhe von beiden Teilen, und die Gesamtstärke? |
#10
|
|||
|
|||
jp
Habe das hier gefunden: Model ist JPL 4300. Billiger zu kaufen wie in 2017! Komplett mit versand und steuer um $ 340
Product Specifications Single Adjusting JackPlate Made of high strength polished Aircraft Quality Aluminum Bronze and Brass hardware eliminate binding Adjusts easily by turning one steel bolt Offers 4 inches of adjustable Vertical movement 3 inches of setback Weighs 23 lbs 225 Maximum Horsepower 1 Year Unconditional Warranty against manufacturer defects JackPlates are the perfect solution for long shaft engines with a short shaft transom! The engine side holes of the JackPlate are drilled 1.500 inches higher than the transom side. Combined with the 4 inches of adjustable vertical lift you can obtain 5.500 inches at a maximum height to raise your long shaft engine and make it workable on a short shaft transom boat! Here are the pre-drilled hole dimensions listed below in inches: Pre-drilled holes for 1/2'' stainless hardware 12 7/8'' across the top two holes from center to center 9 7/8'' across the bottom two holes from center to center 8'' of vertical distance between the top holes and bottom mounting holes Geändert von Drama!! (02.01.2019 um 15:40 Uhr) |
#11
|
|||
|
|||
Ich schreibe dir mal eine Nachricht.
|
|
|
Ähnliche Themen | ||||
Thema | Autor | Forum | Antworten | Letzter Beitrag |
Jack Plate Erfarungen gesucht . | Jens- | Motoren und Antriebstechnik | 21 | 02.11.2017 13:31 |
Jack plate Bezugsquelle | loeti | Motoren und Antriebstechnik | 4 | 13.08.2017 21:54 |
Problem mit Hydraulik jack plate ( Motorlift) | Luckytilo | Technik-Talk | 21 | 11.12.2009 16:13 |
HILFE Wasser durch Transom Plate | kitepro380 | Motoren und Antriebstechnik | 8 | 05.04.2009 10:24 |
Jack Plate - Power Bracket - Powerlift - Hydrolmotorlift | kelt-yamaha | Technik-Talk | 10 | 16.10.2008 22:32 |